说明:
Here is a timelapse of the last 17 months (on and off) work that has gone into saving this 1983 Mk1 Golf GTI Campaign. On first inspection it didn't seem too bad. A little rust here and there yes but a quick tidy up, some fresh fluids and stick an MOT on it. The plan was to use it for the summer then do a light restoration to it. As soon as we started removing parts it was obvious that it was so so much worse than we thought, Rust on nearly every panel meant a massive amount of work and parts was going to be needed. Once it was determined that the car needed a full restoration I set about stripping the car down to a shell and sent it off to be paint stripped and sand blasted to show up every area that required work. This ended up being a lit! Thankfully the guys at Heritage Parts Centre (Link below and a 10% discount code) came in and sponsored the channel and the build providing me with all of the top quality parts I would need to restore the shell. A small list of panels replaced are: Inner sills, Outer sills, Both front floors, Spare wheel tub, Rear panel, Both rear arches, Both inner Rear arches, Scuttle, Front panel, Inner wing, Bonnet, Both wings and we even had to change the roof as the original one was completley rusted out. Once the shell was welded back up and solid again I gave the underside a coat of Upol Etch primer followed by seam sealer and then a coating of Upol Gravitex Stonechip/undersealer. We then set about sanding the outside of the car back to bare metal and with the support of the guys from Breakwells Paints we got the shell primed with a coat of epoxy primer. The shell was then dry guide coated and blocked/sanded back with a 240 grit sand paper to show any high/low spots. Once these were identified we seat about applying the Upol 2k Filler and blocked/sanded those areas flat with 80 grit then 180 grit finishing with 240 grit. Once the filler had been sanded another coat of epoxy primer was added to seal in all of the filler work. The next step was to spray the car with high build primer, dry guide coat it and block/sand the panels so they were all flat and straight. When we were happy with that we build a temporary spray booth with filters in and out to help keep the booth as clean as possible. Now was the time to set about spraying the colour onto the shell. We started off by spraying the underside of the shell then the inside followed by the engine bay and the outside was the final part of the shell. Once dry the shell was removed from the booth and the doors, Boot, Bonnet, Wings, Sun roof were placed in the booth and given the same treatment. The direction of the car changed during the process as the original plane was a concours restoration but as the project went on I realised that this direction was not what I wanted to do. The new direction was to build the show car I have always wanted to, A Shaved bay, 1.8t 20V Mk1 Golf GTI campaign in mars red on air ride. This Time lapse documents the whole restoration start to 'finish' (Are they ever really finished?!) Thank you for watching and thank you to the series sponsors Heritage Parts Centre GT Air Breakwells Paints Tony's Refinishing Dodo Mat Ben's Trim Shop Watch the series from the beginning here: https://www.youtube.com/playlist?list=PLW6s2hBFjAE5XFu3iYgYcynkaljPdlWMa Watch the episode that follows on from this timelapse: https://www.youtube.com/watch?v=0B37zQVEJBs Link to the Dan & Abi YouTube Channel https://www.youtube.com/c/DanAbi Link To Heritage Parts Centre Where you can get 10% off your order by using code 'CHAMBERS' at checkout: https://www.heritagepartscentre.com/uk/ Link to Breakwells Paints: https://breakwellspaints.co.uk/ Link to GT Air: https://gtair.co.uk/ The compressor I have: https://gtair.co.uk/index.php?controller=404 Hi Flow Kit Video: https://www.youtube.com/watch?v=4ZRt5O5n76s Link to Tony’s Refinishing: https://www.youtube.com/c/TonysRefinishingTV Link to the lift I have: Website: https://trommelberg.co.uk/ Instagram: https://www.facebook.com/unsupportedbrowser Facebook: https://www.facebook.com/unsupportedbrowser Link To Heritage Parts Centre Thank you for the jigging points: https://www.heritagepartscentre.com/uk/ Where you can get 10% off your order by using code 'CHAMBERS' at checkout. How nice of them! Want to support the channel? DAC Industries Hoodies, T-Shirts, Wooly Hats, Snapbacks & Stickers are available to buy from my website: https://www.dacind.com My Instagram Account: @dan.a.chambers
准备下载方式
http://unidownloader.com 网站是单独下载视频或音轨的最佳方式。如果您想避免安装程序和扩展。
UDL Helper 扩展是一个方便的按钮,嵌入YouTube、Instagram和OK.ru网站,用于快速下载内容。
UDL Client(适用于 Windows)支持900多个网站、社交网络和视频托管网站的最强大解决方案。包括源中可用的任何视频质量。
UDL Lite–从移动设备访问网站的便捷方式。借助此功能,您可以将视频直接下载到智能手机上。
最佳质量格式为全高清(1080p)、2K(1440p)、4K(2160p)和8K(4320p)。屏幕分辨率越高,视频质量也越高。然而,还有其他因素需要考虑:下载速度、可用空间和设备性能。
浏览器/电脑不应完全冻结!如果发生这种情况,请通过视频链接进行报告。有时视频无法以合适的格式直接下载,因此我们增加了将文件转换为所需格式的功能。在某些情况下,此过程可能会主动使用计算机资源。
您可以使用网站或pwa应用程序 UDL Lite 将视频下载到智能手机上。也可以使用 UDL Helper 扩展通过二维码发送下载链接。
最方便的方法是使用UDL Client 程序,该程序支持将视频转换为MP3格式。在某些情况下,MP3 也可以通过 UDL Helper 扩展下载。
此功能在 UDL Helper 扩展中可用。确保在设置中选中“显示视频快照按钮”。相机图标应出现在播放器的右下角“设置”图标的左侧。单击它时,视频中的当前帧将以 JPEG 格式保存到您的计算机中。
完全不要花钱。我们的服务对所有用户都是绝对免费的。没有PRO订阅,下载视频的数量或最大长度没有限制。