background top icon
background center wave icon
background filled rhombus icon
background two lines icon
background stroke rhombus icon
header logo icon

Download "Монтаж ЦСП на фасад каркасного дома"

input logo icon
"videoThumbnail Монтаж ЦСП на фасад каркасного дома
Table of contents
|

Table of contents

0:00
О чём это видео
0:43
ЦСП для фасада
1:24
Подготовка к монтажу
6:04
Каким образом мы монтировали ЦСП
12:30
Дальнейшая отделка
Similar videos from our catalog
|

Similar videos from our catalog

Video tags
|

Video tags

цсп
фасад
каркасный
дом
каркасник
строительство
монтаж
вентзазор
отделка
Subtitles
|

Subtitles

subtitles menu arrow
  • ruRussian
Download
00:00:00
Hello friends, we started installing DSP
00:00:03
on the facade of my house and in today’s
00:00:06
video I want to tell and show you about the
00:00:09
preparation we did for
00:00:12
this facade, how we install this
00:00:14
material, what kind of fasteners, what we cut it, what
00:00:17
difficulties we encountered
00:00:19
[music]
00:00:43
for my facade I use a DSP board
00:00:47
12 mm thick,
00:00:49
its dimensions are 1250 by 3.20.
00:00:54
Specifically, in my case, we trim it a little so
00:00:56
that we have it at the same
00:00:59
level along all the walls. I recently
00:01:02
had a video on the channel, link in the
00:01:04
description.
00:01:05
So we used this ces slab
00:01:07
as a floor for
00:01:09
We made a so-called platform for the utility unit.
00:01:11
Look, anyone is interested, and a
00:01:15
couple of days ago we started installing it on the
00:01:18
walls and let’s go in order
00:01:21
and start with preparation.
00:01:24
Again, there was a video about
00:01:27
using USB as a windbreak,
00:01:29
I have a house sheathed with it along the racks,
00:01:33
so no film Afterwards, I don’t
00:01:35
use it right away; I sew on the contour of the slats;
00:01:38
the contour of the block; in my case, it’s a board
00:01:41
25 thick, 100 millimeters wide, an
00:01:45
ordinary inch,
00:01:47
and we filled such a board exactly along the racks.
00:01:51
Where the rack is there and the board, it should be noted that the
00:01:55
house was made according to the project and,
00:01:57
accordingly, all the racks were laid out
00:02:00
According to the sheathing
00:02:08
So we started by installing
00:02:12
these boards to the walls, screwing them onto
00:02:15
self-tapping screws like these yellow 6 by
00:02:20
90,
00:02:21
they screw this board to death
00:02:23
properly, especially when
00:02:25
we use an impact screwdriver. Well, a
00:02:28
screwdriver, in principle, will also attract it
00:02:31
further
00:02:35
below we mounted a
00:02:39
perforated corner
00:02:42
25 by 25.
00:02:44
Please note that this corner has
00:02:47
large holes, that is, it comes with
00:02:50
small ones, this one has large holes,
00:02:53
so it can easily
00:02:57
protect our ventilation gap from the penetration of
00:03:00
any mice or other living creatures
00:03:04
into this one just the same ventilation
00:03:06
gap, that is, this is an excellent cheap
00:03:10
alternative to mouse mesh,
00:03:14
steel mesh means in the case when
00:03:18
we make a gap of 25 mm. In general, it’s super
00:03:24
for such screws 25
00:03:33
and due to the fact that friends,
00:03:36
our manufacturer is trying in every possible way to reduce the cost of their
00:03:38
products, here’s this one we are buying a corner
00:03:40
It will be listed on our receipt as 25
00:03:43
by 25 in fact I came and brought it and
00:03:47
tried it on, I don’t understand why it doesn’t
00:03:51
cover the entire gap Why would that be, well, in short,
00:03:54
we live in Russia, friends. You
00:03:56
understand, in short, in fact, it’s somewhere around 22
00:03:58
by 23 Well, that’s how we got out of the situation. Well, what’s
00:04:02
the point? I’m thinking of going to the store now and
00:04:05
looking everywhere for everything, the same thing is most likely on
00:04:08
sale. So keep in mind, I’ll
00:04:11
show you how we’ve now resolved this issue
00:04:14
and even made a little bit of a chisel in our favor to make a
00:04:18
selection like this
00:04:20
and we deepened it a little until
00:04:23
it practically touched
00:04:26
the USB, well, there is a
00:04:27
millimeter gap somewhere, there is no gap at all. At the same time,
00:04:30
when we are installing a split,
00:04:33
we are not bothered by the screw heads, this is also a
00:04:36
plus
00:04:38
under the windows and on the windows we put more
00:04:43
pieces of our sheathing but with these
00:04:48
gaps so that there would be
00:04:50
some kind of air movement here, that is, it
00:04:52
was blown out, went under the ebb and came
00:04:54
out
00:04:55
[music] an
00:04:56
important point regarding the installation of
00:05:00
this ebb, I have it mounted in such a
00:05:03
way that it fits under the OSB
00:05:05
like this as my USB was a temporary
00:05:08
finish, it stood like this for six months.
00:05:10
I wouldn’t want moisture to flow from
00:05:13
the facade and get onto the
00:05:15
foundation and, accordingly, wet the floor
00:05:19
on which the whole house stands. This
00:05:22
board lies flat 50 by 150 for anchorages to
00:05:26
the foundation and so that it it was dry,
00:05:29
I installed the ebb, so all the
00:05:32
moisture drains off, but when installing the DSP,
00:05:35
a difficulty arose in which way the DSP
00:05:38
cannot be supported here, it will melt this
00:05:40
ebb, the DSP is very heavy, one sheet This
00:05:42
is 12 It weighs more than 60 kilograms if
00:05:46
my memory serves me correctly and, accordingly,
00:05:48
I have to hold it on on our fingers
00:05:51
Here we have the DSP floating with the ebb of the tide here
00:05:55
is the vent gap where the air passes and
00:05:58
through this vent gap it comes out that
00:06:01
will come out closer to the roof
00:06:05
How do we mount it How do
00:06:07
we achieve that they are
00:06:10
all at the same level at the bottom so that we have
00:06:14
there was no dancing But in fact, it was
00:06:16
very simple, friends, we nailed it like this,
00:06:19
the nails were first stuffed here, they were stuffed there, they were pulled on the
00:06:23
string, they were punched with 120
00:06:27
nails as stops, and accordingly they
00:06:30
took the sheet, rested it against these nails,
00:06:33
pressed it against the wall and screwed it in.
00:06:36
When installing the DSP boards, be sure
00:06:39
to leave a gap of 6 up to 8 millimeters
00:06:42
at least for this we used two
00:06:45
nails, drove in two nails, two nails of
00:06:47
fours side by side, drove in
00:06:50
the holes left from them and accordingly
00:06:53
we rest the sheet in them and so on, the next one
00:06:56
we screwed the DSP onto self-tapping screws 5 by 50
00:07:01
yellow with preliminary drilling
00:07:06
and we drilled and like that a drill, a drill
00:07:10
and a countersink at the same time,
00:07:13
and advertising for which I don’t get paid
00:07:17
Friends, this is the tool This
00:07:22
drill is just super, it costs something in the
00:07:26
region of
00:07:27
350-380 rubles, but it’s worth it, but it’s
00:07:30
worth it I showed it in the video where we
00:07:34
mounted the platforms we use
00:07:37
with a cheap drill, it’s not at all like this,
00:07:40
friends, it’s really super, it’s already worked for
00:07:44
more than half a house and
00:07:46
drills just amazingly, here
00:07:51
you can clearly see that we’ve drilled it, it’s
00:07:53
deepening the screw, then we
00:07:56
go through this screw with sealant and we all have a flat
00:07:59
surface
00:08:02
when we mounted the DSP on the floor, we sawed it with a
00:08:05
grinder with a diamond blade, in this
00:08:08
case I took an old Interskol disk
00:08:12
with a Gross disk on it and
00:08:14
we tried to saw it. It’s just amazing,
00:08:18
friends. 12 CSP can be sawed without any problems with a
00:08:20
regular saw but with a good disk,
00:08:25
but here you can see the lack of
00:08:28
CSP, a
00:08:29
very, very fragile slab
00:08:34
has been lying around for more than a year,
00:08:37
however, it was
00:08:44
around the edges. In general, in short, there are
00:08:47
cracks like this here, especially
00:08:51
here you can see small cracks, apparently it
00:08:55
nourished moisture and in winter it may have burst,
00:08:59
respectively, when we start carrying
00:09:02
this sheet, it’s like this Chrome and that’s all
00:09:05
Total friends, a whole sheet 1250 by 3200,
00:09:09
four of us need to carry it, two people on
00:09:13
each side of the sheet, take our hands,
00:09:14
spread them wider and carry the sheet just
00:09:17
like that,
00:09:19
friends, four of us need to mount it, and three of us need to
00:09:23
mount it. There’s nothing you can do here, you
00:09:26
can physically lift it, but there is a high
00:09:29
probability that when lifting it, it will
00:09:31
simply break there is, you need to carefully
00:09:33
lift it from a horizontal
00:09:35
position, vertical In general, well, it’s
00:09:39
quite a labor-intensive process, but in
00:09:41
principle everything turns out quite quickly.
00:09:44
Here we have prepared sheets for installation, which means we put
00:09:49
three supports under them
00:09:53
and threw battens on these supports, here
00:09:56
you can have four battens from below you can also see this is
00:10:05
how they lie, these sheets of DSP, right there
00:10:08
we mark them, saw them, cut them,
00:10:12
pre-drill them, and only in
00:10:15
this form carry them into place;
00:10:18
as for cutting from USB, it’s easier; to
00:10:29
apply marking is
00:10:31
very labor-intensive, a lot of effort is wasted,
00:10:34
so I try to basically
00:10:35
measure everything out, since everything is more or less even
00:10:37
when
00:10:39
assembling the wall, we always align the
00:10:42
outer plane
00:10:44
and, accordingly, in principle, all the
00:10:46
geometric dimensions, there is no special dance,
00:10:50
we measured it, we calculated it, we cut it
00:10:53
right on the spot and then this
00:10:56
was installed with some gaps there
00:10:58
but that’s normal Friends gave the finishing of the
00:11:01
window opening frame the whole thing will be
00:11:03
closed
00:11:04
This is how it all turns out, there are
00:11:07
some
00:11:08
gaps and according to the level here exactly at the top
00:11:13
for example
00:11:15
a little bit we gave a margin
00:11:24
installation of sheets we start from the center to the edge
00:11:28
So In this way, all the seams we have
00:11:32
come out even,
00:11:34
the only thing that needs to be done is that the first sheet must be placed according
00:11:36
to the level; you can outline a
00:11:39
line on the sheathing and use it to guide you during installation;
00:11:42
in principle, the first
00:11:44
sheet was set; everyone else went
00:11:46
just in one go.
00:11:48
Well, I’ll show you the jamb, the
00:11:51
jamb, this is the
00:11:54
plan here. as if it turned out
00:11:57
that this sheathing, which is there behind the DSP,
00:12:02
I didn’t make a cut for the corner; the head of the
00:12:06
screw sticks out only a millimeter.
00:12:08
But it was enough for that, when
00:12:10
attracting this screw, the
00:12:14
corner rested against this head of the self-tapping screw
00:12:17
and burst now I don’t know what to do with it
00:12:21
but this is what we need to
00:12:24
avoid, in short, DSP is such a capricious
00:12:26
material. That’s
00:12:28
exactly what we’re talking about in
00:12:30
terms of further finishing, friends,
00:12:33
there are several options, including painting
00:12:37
and
00:12:40
plaster, there are special
00:12:43
elastic plasters that go specifically to DSP and
00:12:46
even OSB, but friends, it’s all [ __ ] the fact is that
00:12:50
they are very expensive,
00:12:51
the plaster itself is expensive, the work is expensive, and
00:12:54
plus everything else, the result
00:12:56
is kind of a little bit, but not that it’s not
00:13:00
clear, but with my own eyes, I
00:13:03
don’t have any experience who has used such
00:13:06
plaster, how durable it is
00:13:07
is unclear and you don’t know how much
00:13:10
money to spend This plaster
00:13:13
looks cool. It’s beautiful, but we’ll
00:13:15
probably stop at painting,
00:13:18
we’ll fix these self-tapping screws, we’ll paint it,
00:13:22
maybe we’ll make
00:13:24
wooden flashings for the seams. Since I will have an imitation of
00:13:26
timber, in the future I’ll also have inserts throughout the
00:13:29
house, that is, the combination will be a DSP facade
00:13:31
Imitation of timber in general, we'll see in the
00:13:34
next videos, friends, I'll
00:13:35
be sure to show you
00:13:38
Who has any questions Maybe
00:13:40
I forgot something, maybe I didn't
00:13:42
tell you something, I didn't prove it Be sure to write
00:13:43
in the comments I
00:13:45
'll be glad to talk to everyone I wish you health,
00:13:48
good luck, good luck Take care of yourself for now

Description:

В качестве фасада для своего каркасного дома выбрал плиты ЦСП. Сначала сделали подготовку - набили обрешетку из доски 100х25 мм, смонтировали перфорированный уголок от грызунов. После приступили к монтажу ЦСП на стены фасада. О том, с какими трудностями в работе столкнулись, какими инструментами и как работали - обо всём рассказываю в видео. Приятного просмотра! Видео про использование ЦСП в качестве платформы для каркасного хозблока https://www.youtube.com/watch?v=giA574xb8F0 Видео про использование ОСБ в качестве ветрозащиты https://www.youtube.com/watch?v=9dEz6OfaeUA Проект Каркасного дома 9х12м https://vk.cc/cw50rg Тайм-коды 00:00 О чём это видео 00:43 ЦСП для фасада 1:24 Подготовка к монтажу 6:04 Каким образом мы монтировали ЦСП 12:30 Дальнейшая отделка Связаться со мной по вопросам проектирования и строительства: по телефону или WhatsApp +7(904)291-36-50 по электронке [email protected] (посредине ноль) Подписывайтесь: ВКонтакте vk.com/necardhome Телеграм t.me/necardhome Дзен dzen.ru/necardhome Наш сайт некарточныйдом.рф https://vk.cc/cw4Zgm

Preparing download options

popular icon
Popular
hd icon
HD video
audio icon
Only sound
total icon
All
* — If the video is playing in a new tab, go to it, then right-click on the video and select "Save video as..."
** — Link intended for online playback in specialized players

Questions about downloading video

mobile menu iconHow can I download "Монтаж ЦСП на фасад каркасного дома" video?mobile menu icon

  • http://unidownloader.com/ website is the best way to download a video or a separate audio track if you want to do without installing programs and extensions.

  • The UDL Helper extension is a convenient button that is seamlessly integrated into YouTube, Instagram and OK.ru sites for fast content download.

  • UDL Client program (for Windows) is the most powerful solution that supports more than 900 websites, social networks and video hosting sites, as well as any video quality that is available in the source.

  • UDL Lite is a really convenient way to access a website from your mobile device. With its help, you can easily download videos directly to your smartphone.

mobile menu iconWhich format of "Монтаж ЦСП на фасад каркасного дома" video should I choose?mobile menu icon

  • The best quality formats are FullHD (1080p), 2K (1440p), 4K (2160p) and 8K (4320p). The higher the resolution of your screen, the higher the video quality should be. However, there are other factors to consider: download speed, amount of free space, and device performance during playback.

mobile menu iconWhy does my computer freeze when loading a "Монтаж ЦСП на фасад каркасного дома" video?mobile menu icon

  • The browser/computer should not freeze completely! If this happens, please report it with a link to the video. Sometimes videos cannot be downloaded directly in a suitable format, so we have added the ability to convert the file to the desired format. In some cases, this process may actively use computer resources.

mobile menu iconHow can I download "Монтаж ЦСП на фасад каркасного дома" video to my phone?mobile menu icon

  • You can download a video to your smartphone using the website or the PWA application UDL Lite. It is also possible to send a download link via QR code using the UDL Helper extension.

mobile menu iconHow can I download an audio track (music) to MP3 "Монтаж ЦСП на фасад каркасного дома"?mobile menu icon

  • The most convenient way is to use the UDL Client program, which supports converting video to MP3 format. In some cases, MP3 can also be downloaded through the UDL Helper extension.

mobile menu iconHow can I save a frame from a video "Монтаж ЦСП на фасад каркасного дома"?mobile menu icon

  • This feature is available in the UDL Helper extension. Make sure that "Show the video snapshot button" is checked in the settings. A camera icon should appear in the lower right corner of the player to the left of the "Settings" icon. When you click on it, the current frame from the video will be saved to your computer in JPEG format.

mobile menu iconWhat's the price of all this stuff?mobile menu icon

  • It costs nothing. Our services are absolutely free for all users. There are no PRO subscriptions, no restrictions on the number or maximum length of downloaded videos.