Download "Fabricación de mini torno casero"

"videoThumbnail Fabricación de mini torno casero

Regulador PWM para LEDs (muy facil de hacer)

Regulador PWM para LEDs (muy facil de hacer)

Channel: Proyectos LED

¨QUIEN ES QUIEN¨ CASERO

¨QUIEN ES QUIEN¨ CASERO

Channel: Los talleres de Elena

como "reparar" lampara LED G9

como "reparar" lampara LED G9

Channel: Proyectos LED

Drill Press, Lathe and Router Table in one Tool / Part 1

Drill Press, Lathe and Router Table in one Tool / Part 1

Channel: Paoson Woodworking

Самодельная фрезерная погружная база для бормашины.

Самодельная фрезерная погружная база для бормашины.

Channel: Paoson Woodworking

Omar Acedo - Adicto (Video Oficial)

Omar Acedo - Adicto (Video Oficial)

Channel: Omar Acedo

Torno

fresadora

plato

venezuela

casero

torno casero

plato divisor

mini torno

00:00:00

Good afternoon YouTube friends.

00:00:03

Here I am going to present you a project that

00:00:06

I have had for a long time about How to

00:00:10

make a homemade lathe, a homemade mini lathe,

00:00:12

right, I am going to show you what

00:00:15

the steps are, what I did and what I

00:00:17

did with what material and

00:00:23

for what. You guys watch this video

00:00:25

because the first thing I did was look for a

00:00:29

6 by 3 inch tube, this tube that

00:00:32

you see here,

00:00:34

then

00:00:39

I looked for a gimbal tube for a car gimbal

00:00:44

and I made two sleeves and put them under pressure

00:00:47

here to later insert the

00:00:49

bearings. from here on this side

00:00:51

[Music]

00:00:53

right then I made the axis

00:00:58

and left it right

00:01:02

and

00:01:04

also get

00:01:06

these doublet beams right

00:01:11

so that you could serve as a support

00:01:14

for the screw

00:01:17

the other thing I made was the blade holder I

00:01:21

did it with one with a medium flash

00:01:25

inch

00:01:28

then I grabbed a cylinder

00:01:30

The Two From here to give me the

00:01:33

height from here

00:01:35

here I placed the base of the transverse carriage

00:01:42

as you can see

00:01:45

I got two calibrated tubes of automobile

00:01:49

shock absorber rod

00:01:51

also

00:01:54

that already comes to an exact measurement

00:02:00

as you can see here This bar that

00:02:03

comes calibrated I

00:02:05

also made the longitudinal carriage,

00:02:07

right

00:02:10

here with a one-inch screw with

00:02:12

its one-inch nut down here, the

00:02:14

same as the transverse carriage here, place

00:02:17

two bearings,

00:02:19

right, the 1 and 3/8

00:02:23

by half-inch bearings

00:02:26

so that the axis rotates on the

00:02:28

bearings and can move the transverse carriage the

00:02:33

same as the longitudinal carriage

00:02:39

I used two bearings one bearing here and

00:02:41

I put one at this end also the

00:02:45

same here and here

00:02:50

the other thing I did was to

00:02:54

make the point the head

00:03:04

[Music]

00:03:08

as a steel material

00:03:11

Here As you can see

00:03:15

in here I have a screw that is going to

00:03:18

remove the point, right,

00:03:21

it is going to come out and go in.

00:03:26

The other thing I did was make the base of the

00:03:29

motor,

00:03:31

I did the same operation of the

00:03:33

cross carriage here

00:03:36

with its one-inch screw

00:03:39

and its nut Already under welded this to

00:03:42

tension the motor

00:03:46

as you can see

00:03:48

the motor enters

00:03:51

and exits this to tension it

00:03:56

This is a 220 single phase motor

00:04:03

the rotating point I also made of

00:04:07

steel this is all enclosed everything

00:04:09

Here I am going to explain how the

00:04:13

point works of rotating points

00:04:23

you can see it is coming out here,

00:04:32

really inside it has its slot the

00:04:35

screw prevents it from going to one side

00:04:37

and it is coming out

00:04:40

remember that it is a homemade mini lathe

00:04:46

Now the most important thing about this lathe

00:04:51

is also the mandrel The plate

00:04:54

The plate I made it a homemade dish too.

00:04:58

Here I'm going to show you how I made it. These grinding

00:05:01

wheels that you see here were from a

00:05:04

chuck. It's good that they were going to give it to me but

00:05:07

they never gave it to me, but the grinding wheels did

00:05:09

fit and I took advantage of the grinding wheels. I

00:05:12

had to temper them. the untempered sorry

00:05:15

untempered with a blowtorch to be able to

00:05:17

drill and make the three-

00:05:19

eighths thread rosapina once I made the

00:05:23

thread truth

00:05:24

[Music]

00:05:25

alma muela

00:05:27

I

00:05:28

got three screws also with three-

00:05:32

eighths fine threads and what you

00:05:34

see here are nuts too but I

00:05:37

rounded them and drilled them, they

00:05:41

removed the threads from the nuts,

00:05:43

right, later I made the groove and

00:05:48

the grooves here so that the grinding wheel

00:05:53

moves up and down,

00:05:57

these nails, which all of this must

00:05:59

have a guide here, also that prevents them from The

00:06:03

tooth moves outwards,

00:06:08

here I show you, look, I did

00:06:12

n't solder it, I made a hole in it and put

00:06:17

a little cup in it, right, so I can take it out

00:06:20

and it also turns the wheels upside down so that they

00:06:23

can be used

00:06:24

to hold the pieces upside down, also

00:06:28

a Madrid of this is costing a lot

00:06:30

money, I made it with three wheels, there are

00:06:33

many people who make it with four wheels, but

00:06:35

I only had three, I'm going to show you

00:06:37

here how it goes

00:07:03

and here you are centered in Madrid.

00:07:08

I made this in three centered for

00:07:12

[Music]

00:07:13

to be able to

00:07:16

get into the point. To align the lathe

00:07:20

the screw

00:07:26

is almost aligned the lathe

00:07:30

after we are well centered well

00:07:32

aligned we are going to weld here but

00:07:34

we are going to weld it with bronze with bronze

00:07:37

here so that it looks much better

00:07:41

as you can see it is a homemade mini lathe

00:07:44

I hope this This video will serve as an

00:07:47

inspiration to many turners who

00:07:51

have this factory concern. A

00:07:53

homemade lathe can be done like this, but with a

00:07:56

little patience and with

00:07:57

recycled material, here I show you and leave you this

00:08:00

small video. I hope you like it and that it is

00:08:03

of some use to you. Thank you very much.

Description:

soy Venezolano del estado Zulia,siempre tuve el anhelo de fabricar un mini torno casero con poco material recuperable, primero por que amo esta profecion y lo que hago lo hago con amor y con pacion y a Dios le doy gracias por tener mi propio taller hoy en dia,tengo muchos años trabajando como tornero y a los italianos españoles colombianos peruanos argentinos mil gracias por que a utdes les debo todo lo q

Preparing download options

Popular

HD video

Only sound

All

* — If the video is playing in a new tab, go to it, then right-click on the video and select "Save video as..."

** — Link intended for online playback in specialized players

Questions about downloading video

How can I download "Fabricación de mini torno casero" video?

http://unidownloader.com/ website is the best way to download a video or a separate audio track if you want to do without installing programs and extensions.
The UDL Helper extension is a convenient button that is seamlessly integrated into YouTube, Instagram and OK.ru sites for fast content download.
UDL Client program (for Windows) is the most powerful solution that supports more than 900 websites, social networks and video hosting sites, as well as any video quality that is available in the source.
UDL Lite is a really convenient way to access a website from your mobile device. With its help, you can easily download videos directly to your smartphone.

Which format of "Fabricación de mini torno casero" video should I choose?

The best quality formats are FullHD (1080p), 2K (1440p), 4K (2160p) and 8K (4320p). The higher the resolution of your screen, the higher the video quality should be. However, there are other factors to consider: download speed, amount of free space, and device performance during playback.

Why does my computer freeze when loading a "Fabricación de mini torno casero" video?

The browser/computer should not freeze completely! If this happens, please report it with a link to the video. Sometimes videos cannot be downloaded directly in a suitable format, so we have added the ability to convert the file to the desired format. In some cases, this process may actively use computer resources.

How can I download "Fabricación de mini torno casero" video to my phone?

You can download a video to your smartphone using the website or the PWA application UDL Lite. It is also possible to send a download link via QR code using the UDL Helper extension.

How can I download an audio track (music) to MP3 "Fabricación de mini torno casero"?

The most convenient way is to use the UDL Client program, which supports converting video to MP3 format. In some cases, MP3 can also be downloaded through the UDL Helper extension.

How can I save a frame from a video "Fabricación de mini torno casero"?

This feature is available in the UDL Helper extension. Make sure that "Show the video snapshot button" is checked in the settings. A camera icon should appear in the lower right corner of the player to the left of the "Settings" icon. When you click on it, the current frame from the video will be saved to your computer in JPEG format.

What's the price of all this stuff?

It costs nothing. Our services are absolutely free for all users. There are no PRO subscriptions, no restrictions on the number or maximum length of downloaded videos.