Download "Вся правда о циркулярках на примере Прораб 5602"

Please wait. We're preparing links for easy ad-free video watching and downloading.

Next video: Универсальная токарная головка

Универсальная токарная головка

Универсальная токарная головка

Channel: HeARTwood

деревообработка

мастер-класс

видеоурок

wood

wooden

фугование

строгание

Woodworkers

фуганок

рейсмус

циркулярка

циркулярная

дерево

столярка

столярная мастерская

обучение

видео урок

мебель

учимся

изготовление

создание

склеиваем щит

фугуем

строгаем

столярное производство

цех

дуб

ясень

красное дерево

обработка

фрезер

фрезерование

долбление

пиление

резьба

DIY

строительная пила

столярная пила

обзор

сравнение

00:00:00

[music]

00:00:12

Hello, dear viewers and

00:00:13

subscribers, I am again glad to welcome

00:00:15

you to the channel har My name is Mikhail in

00:00:18

continuation of the topic about the circular saw Today we

00:00:20

will look at such a circular saw,

00:00:23

this is the foreman

00:00:24

5602, someone already has this saw, someone

00:00:27

is just going to buy it and today we

00:00:29

will not make a small review, I will immediately say

00:00:32

that this is not a carpenter’s saw, it is a

00:00:33

construction saw. Therefore, if you

00:00:36

are counting on buying it and using it in

00:00:39

the manufacture of furniture, then you will face very

00:00:43

big problems, a lot of difficulties

00:00:45

when working with this saw. Of course, I will not

00:00:47

say that the saw is completely

00:00:49

inoperable. I bought it in

00:00:51

order to cut rough material, but

00:00:54

nevertheless, apart from exactly how to cut rough

00:00:56

material, it is not capable of anything else.

00:00:58

This saw has a kiva of power;

00:01:01

its maximum cut is 80

00:01:03

mm. You can also tilt the disk

00:01:07

at 45° or in any other position everything

00:01:10

is done with the help of a handwheel. I

00:01:13

’ll show you this now, of course, the saw is inexpensive in

00:01:15

comparison with any stationary

00:01:17

circular saw like Makita or Devo,

00:01:20

it’s just a cheap saw, but

00:01:22

nevertheless, I’ll repeat it again, it’s a saw. The

00:01:24

construction saw is

00:01:26

naturally equipped with a saw blade with a diameter of 254

00:01:29

mm, a

00:01:31

mobile carriage which goes into the

00:01:34

left or right of the disk and such a

00:01:37

parallel stop Unfortunately, it came to me as

00:01:39

unusable and broke off.

00:01:42

Well, in short, this is a ruler that

00:01:45

is placed in any desired

00:01:48

position, so the clamp itself is quite

00:01:51

good. It fits here at

00:01:55

the ends of the

00:01:58

floor. But honestly, the parallelism is

00:02:02

here disk and this ruler are not

00:02:05

carried out and are not adjusted and, as a

00:02:08

rule, it turns out that either the workpiece

00:02:11

moves away from this parallel stop

00:02:14

or runs into it and begins to wedge,

00:02:17

that is, this thing, even with all

00:02:19

its thoughtfulness, it is useless. Well,

00:02:23

naturally, the kit also comes with

00:02:25

two keys in order to replace

00:02:27

the disk, in a nutshell, this saw has

00:02:30

much more disadvantages than advantages. Of

00:02:33

the advantages, the ruler that can be

00:02:37

cut is wide, these table extensions

00:02:40

It comes in a box, quite compact,

00:02:43

then these table extensions are

00:02:44

installed under the braids but on their

00:02:47

own they are made of stamped

00:02:49

metal, the rigidity here is, in principle,

00:02:52

sufficient, but you should not expect that you

00:02:54

will get a perfectly flat plane, that

00:02:56

is, it is impossible to cut sheet material or

00:02:58

bars on this saw. I will immediately

00:03:02

say about the saw blade, a

00:03:04

saw blade with a diameter of 254 mm is used, but

00:03:07

the problem is that this disk

00:03:09

mounting hole, that is, the

00:03:11

shaft diameter is 16 mm, and here a very

00:03:14

big problem arises. The problem is that if

00:03:16

you want to use

00:03:18

some branded disk on this saw, for example fre

00:03:20

Makita or something else, then I draw

00:03:22

your attention to the fact that branded disks are

00:03:24

everywhere for normal people, the landing

00:03:26

diameter is 30 or 32 mm, these are two

00:03:30

international

00:03:32

standards, to show what the problem is,

00:03:34

I will use the sole from the router,

00:03:37

imagine that this is a landing washer

00:03:39

that is installed on the shaft of a

00:03:41

circular saw, its shaft has a diameter of 16

00:03:45

mm, and we install a disk, for example, with an

00:03:47

internal diameter of 30 mm Naturally, you

00:03:50

need to put a spacer here, but

00:03:53

the problem is that in this washer on this

00:03:55

machine there is a very deep

00:03:58

recess,

00:04:00

you can unscrew it and see if there is a working

00:04:03

point, or rather a contact area, and a

00:04:07

small recess must be made;

00:04:08

this is necessary to ensure

00:04:11

reliable grip of the disk clamping along the

00:04:14

outer radius of the washer. the central

00:04:17

part is here. On the contrary, it should have a little bit of a

00:04:19

gap from the disk in this machine,

00:04:22

this one, this recess is made so

00:04:25

deep that when installing the disk and

00:04:28

the spacer, it simply falls into this

00:04:31

recess and the disk falls. I even had

00:04:34

one case where I was

00:04:36

very careful with glue dripped a little,

00:04:39

fixed the spacer inside the disk,

00:04:41

put it on the washer, when I tightened it, it

00:04:44

turned out that the washer just fell out

00:04:47

anyway, and my disk shifted a little bit.

00:04:49

Naturally, during work, the saw started

00:04:51

jumping, I turned it off in time, as

00:04:54

a matter of fact, well, it’s dangerous for

00:04:57

health, then Rome this insert, I’ll

00:05:00

turn the saw so that you can better

00:05:03

see the plastic liner, you can see that

00:05:06

its rigidity is completely

00:05:09

insufficient; then the liner itself has

00:05:11

less thickness than the depth of this

00:05:14

groove into which it is screwed.

00:05:16

Naturally, here you

00:05:18

have to put some kind of cardboard or veneer;

00:05:28

you see, one screw is no longer there,

00:05:32

because here it’s all

00:05:34

silumin casting, then naturally the screws

00:05:36

bite, the thread deteriorates and even from

00:05:40

vibration these screws begin to

00:05:41

unscrew, one screw is completely

00:05:43

jammed. I had to break it out and then

00:05:45

unscrew it with pliers.

00:05:47

The axis of the tilt mechanism is located on the

00:05:50

bottom side of the table top and naturally

00:05:53

when uh, changing the angle of inclination, the disk moves

00:05:56

to the side for this. This bevel was made.

00:05:59

Well, as you understand, this bevel is

00:06:01

naturally located quite

00:06:03

close to the disk and it is located

00:06:06

directly in the work area,

00:06:08

so any scrap that

00:06:11

gets here will definitely be

00:06:14

pulled into a circular and here is the protection

00:06:17

Well, it’s probably not visible here already I

00:06:19

have a crack here, a hole, that is,

00:06:22

any workpiece, any sliver that

00:06:24

gets into this crack is sure

00:06:26

to tighten it and it even happened that

00:06:28

the disk got jammed

00:06:30

and now I focused my attention on the next

00:06:32

point after watching two

00:06:34

videos on Makita and on the

00:06:36

Baikal circular saw converted for installation in a table.

00:06:39

Many people started asking me questions, what

00:06:41

difference does it make, think about it, the tilt of the disk goes

00:06:44

to the side, no big deal, it cuts just the same,

00:06:46

you can put plywood on top

00:06:49

and it’s okay, or let’s say we

00:06:51

provide liners with zero clearance

00:06:53

under each sawing angle of the guys. all

00:06:56

dancing with a tambourine The fact is that the carpenter's

00:06:58

circular saw is

00:07:00

structurally very high

00:07:01

cutting accuracy, plus on top of everything it is

00:07:04

designed to save your

00:07:06

time, save in terms of setting,

00:07:09

I turned the saw so that it was better visible and the

00:07:12

point is that the ruler is

00:07:15

installed here on the front bar,

00:07:17

its zero mark must exactly

00:07:19

coincide with the plane of the disk where it is

00:07:23

placed on the washer, here there can

00:07:26

only be a correction for the thickness of the tooth, most

00:07:28

often stat dis, so once we set

00:07:32

this ruler, we don’t touch it anymore.

00:07:34

But as soon as we change the inclination of the disk, then

00:07:37

Naturally, the cutting line goes away and

00:07:40

how far it went, it’s very

00:07:43

difficult to navigate, let’s look at a specific

00:07:46

example: my original fence is broken off, I

00:07:49

use this bar, for example, we have

00:07:51

set some sawing width, we

00:07:54

need to saw off the workpiece exactly

00:07:56

98 mm in width, we begin to tilt

00:08:07

the disk You you see that the disk’s plane

00:08:10

is moving away and approaching the

00:08:12

stop Let’s now try to

00:08:15

somehow set the required width How to

00:08:19

measure what to

00:08:21

focus on here everything is quite difficult,

00:08:23

that is, as you understand, it is

00:08:28

absolutely impossible to accurately set a parallel stop relative to the inclined one,

00:08:30

since the zero mark has

00:08:32

moved to the side

00:08:34

control option - This is a test cut. Well, for example,

00:08:36

we take a workpiece, set the stop to the desired

00:08:39

position approximately. It seems to us that

00:08:42

we take any workpiece, make a test

00:08:46

cut, measure the distance, see how much

00:08:48

we were wrong and correct this distance

00:08:51

to a plus or minus,

00:08:53

maybe if we do it again Ole Well, I know

00:08:58

We are not capable, I don’t have enough patience for this.

00:09:01

Therefore, I made exactly

00:09:04

the option with a manual circular saw that

00:09:07

remains in the table. It’s a very simple light

00:09:09

circular saw, but its cutting line, the zero

00:09:11

mark, remains the same all the time.

00:09:13

I set the stop once And along it

00:09:16

Then you can work completely

00:09:19

painlessly Well, I’ll just say a few words

00:09:21

about the stop for facing,

00:09:24

here two tracks are made on the left and right, the

00:09:28

stop itself is very

00:09:30

flimsy,

00:09:32

so we insert it and get crazy backlashes, that is,

00:09:35

work on it Well, let’s say it’s possible,

00:09:38

but all this turns out to be

00:09:40

normal I’m confused one moment,

00:09:44

two drillings are made, the screws are tightened. For

00:09:46

what purpose this remains a mystery to me

00:09:47

to this day. For example, in order to

00:09:50

insert the stop, you need to unscrew this screw;

00:09:53

in principle, it works normally, but

00:09:55

when the screw is tightened, the stop is not inserted.

00:09:59

If it was meant that the screw is needed

00:10:01

in order for this stop for facing it’s

00:10:04

not lost It’s not clear to me then it’s not clear to

00:10:06

unscrew it, tighten it every time to remove it, it’s

00:10:08

inconvenient That is, this

00:10:11

remains a mystery for me Well, okay, let’s leave it, in

00:10:13

principle, there are no complaints here, two

00:10:16

tracks allow you to move this plate

00:10:19

to the desired position,

00:10:21

fix it, and also release the screw, loosen the

00:10:25

usual protractor, change the angle of inclination

00:10:28

there’s nothing here,

00:10:30

as I already mentioned, these crazy backlashes

00:10:34

I didn’t make a selection of backlashes Although this is

00:10:37

done very easily, I’ll show you with an

00:10:39

example of how I did it on a

00:10:42

band saw Now I won’t get stuck on this,

00:10:44

let’s look at the saw

00:10:47

from the inside, you can immediately see it’s probably rushing

00:10:50

In your eyes, of course, this corrugation is

00:10:52

removed, the corrugation was removed because it is in

00:10:55

any case no matter how you put it in. It has a

00:10:58

very large

00:11:00

bend. Besides, the passage hole

00:11:03

here is so small that

00:11:06

chips fly through here very poorly and this

00:11:09

pipe gets clogged, but also the matter

00:11:12

is complicated by the fact that this circular machine

00:11:14

by itself snatches out pieces of wood and

00:11:17

these pieces of wood chips are clogged here in the

00:11:21

corrugation and the chips just don’t get removed.

00:11:24

I

00:11:26

once couldn’t understand why my

00:11:28

chips were flying up, it turned out that she had filled

00:11:31

this corrugation with chips and they were all the way on the

00:11:34

back side. here on the bends

00:11:36

they climbed out like a hedgehog I use it

00:11:39

without a removal field I just have a

00:11:42

thick cardboard box, the box is

00:11:45

covered with this kind of plywood and all

00:11:48

the shavings pour directly

00:11:49

from here down into the box, that is, here

00:11:51

I don’t have any problems now

00:11:54

let’s look at the adjustments first In total, the

00:11:57

lifting adjustment

00:12:00

was done using a

00:12:02

flywheel. So, well, there’s nothing complicated here,

00:12:07

so the screw tightens the nut and

00:12:12

raises the saw. I also wanted to say that I forgot to say that there was a riving

00:12:15

knife right away.

00:12:19

The mechanism is made here. There’s a lever. It

00:12:23

allows you to lower and raise the saw

00:12:26

together with the riving knife. According to the

00:12:29

idea, it can it’s not bad, of course, but it

00:12:31

works so-so. Once again I’ll show you how the

00:12:34

lifting mechanism works. The screw that goes

00:12:38

through this

00:12:46

boss is like this. The

00:12:48

lifting and lowering, of course, there are big gaps,

00:12:56

that’s all. The tilt mechanism is the same thing. The

00:13:00

screw here is a floating boss with gaps. Nuno,

00:13:02

this is also a standard solution

00:13:04

here. there seems to be nothing new As

00:13:07

you can see the corrugation, no matter how you install it,

00:13:11

it still bends very much, that

00:13:13

is, this element is completely

00:13:14

useless, removal chips here are

00:13:18

worthless, that is, this is how

00:13:21

the adjustment is carried out, here you

00:13:25

see the magnetic starter, protection here

00:13:27

seems to be a problem none If suddenly the

00:13:30

voltage is lost, the saw turns off and

00:13:32

again when the voltage is applied, the saw

00:13:34

no longer turns on spontaneously, and now

00:13:36

let’s look at the biggest problem with

00:13:38

this saw. Of course, each of you has

00:13:41

definitely encountered the situation when the disk

00:13:44

comes into resonance with the material, that

00:13:46

is, the saw starts to rattle and twitches

00:13:48

very well it cuts quickly but with a roar,

00:13:51

this is a distinctive property of these saws. The

00:13:53

fact is that their suspension mechanism is very poorly made;

00:13:56

it is made of one

00:13:59

single axis, which is located

00:14:02

here in the front part, that is, in the back

00:14:04

part there is nothing here, the entire mechanism

00:14:08

is attached to one single point

00:14:10

Now I’ll try to show you some light, here’s a

00:14:13

plate that secures the back of the

00:14:16

axle, and you can see from the front this

00:14:23

axis, that is, the only axis on

00:14:25

which this mechanism tilts back and forth; the

00:14:28

second fulcrum is the

00:14:30

front wall. That is, when we

00:14:33

tighten this adjustment nut.

00:14:40

you see the saw begins to rattle and the

00:14:43

front wall literally shakes,

00:14:46

that is, when working, this wall

00:14:50

begins to rattle and the whole saw

00:14:52

shakes slightly and begins to snatch

00:14:54

large chips from the material. That is, as I

00:14:57

said, this is a saw, it is not suitable for

00:15:00

use in as a

00:15:03

carpenter, I’ll show you again a little about the

00:15:07

problems with lighting. This whole unit

00:15:10

is attached to one single axis

00:15:12

that runs from the back to the

00:15:15

front, this axis can be

00:15:17

seen here it sticks out, one cover is screwed here

00:15:19

and the second cover is screwed here,

00:15:22

these covers are like once and

00:15:25

hold the axis And then this is the

00:15:27

constructive Emen Serga which

00:15:30

is the basis for the suspension of this entire

00:15:33

mechanism. In general, that is, the fastening

00:15:35

occurs only at one single

00:15:37

point, in the front part of this

00:15:39

rigidity,

00:15:41

rattling occurs completely insufficiently, this saw tears the

00:15:43

material, it snatches out pieces and

00:15:45

chips break off, this is just

00:15:47

because the design with half rings is

00:15:50

used in carpentry saws for a reason, it

00:15:53

is the design with half rings that

00:15:55

is able to set the necessary rigidity and

00:15:57

precision of processing. This is all rubbish,

00:16:01

let's listen to how this saw works,

00:16:03

right away I will say it roars just

00:16:18

terribly, the only Joy in this saw

00:16:21

has a dynamic brake when you press the

00:16:23

stop button, the saw stops very

00:16:26

quickly, otherwise you see I tried

00:16:31

to cut this oak, well, to be honest, one and a half

00:16:35

kilowatts of power is not enough to

00:16:38

cut such material, the thickness is

00:16:41

about 50

00:16:43

mm, another conclusion I wanted to address to the

00:16:46

audience in particular to those who asks

00:16:49

questions about my

00:16:51

videos, the questions were of the following

00:16:54

nature: People ask what is the

00:16:56

difference between this circular table, these are the

00:16:59

same mata and Baikal Why

00:17:01

can one be put on the table Why

00:17:03

can’t the other one At first I thought that Well,

00:17:07

probably I said something wrong

00:17:09

or didn’t

00:17:11

explain it clearly enough Well, maybe somewhere I made a mistake with

00:17:13

the wording, it also happens. But on the other

00:17:16

hand, for me it’s like saying this is

00:17:19

good news for me because I

00:17:20

feel that the audience is interested in me, but

00:17:23

for me it’s important, I try to make

00:17:25

videos so that you’ll be interested in

00:17:27

watching so that you were able to glean

00:17:30

something new from them and learn something for yourself,

00:17:32

so don’t hesitate to ask

00:17:34

questions. You can do this in

00:17:36

the comments under the video itself or

00:17:39

write to me in one of the contacts that are

00:17:40

listed in the description of the videos. Well,

00:17:43

I’m with you on this goodbye I hope this

00:17:45

video was educational for you, bye everyone

Description:

Подробный обзор стационарной пилы Прораб 5602. В ролике показаны все преимущества и недостатки. Также проведена аналогия с другими пилами и показаны конструктивные особенности и отличия строительных и столярных пил. Страница Фэйсбук: https://www.facebook.com/unsupportedbrowser ЖЖ: https://mazai-san.livejournal.com/ Музыка: https://www.audiomicro.com/ Звуковые эффекты: https://www.audiomicro.com/sound-effects Сбербанк 4276 1609 0418 0388 Мои дополнительные официальные ресурсы: Телеграм-канал https://t.me/HeARTwood_official Канал Рутьюб https://rutube.ru/channel/23832669/ Группа на ВК https://vk.com/club78263279

Preparing download options

Popular

HD video

Only sound

All

* — If the video is playing in a new tab, go to it, then right-click on the video and select "Save video as..."

** — Link intended for online playback in specialized players

Questions about downloading video

How can I download "Вся правда о циркулярках на примере Прораб 5602" video?

http://unidownloader.com/ website is the best way to download a video or a separate audio track if you want to do without installing programs and extensions.
The UDL Helper extension is a convenient button that is seamlessly integrated into YouTube, Instagram and OK.ru sites for fast content download.
UDL Client program (for Windows) is the most powerful solution that supports more than 900 websites, social networks and video hosting sites, as well as any video quality that is available in the source.
UDL Lite is a really convenient way to access a website from your mobile device. With its help, you can easily download videos directly to your smartphone.

Which format of "Вся правда о циркулярках на примере Прораб 5602" video should I choose?

The best quality formats are FullHD (1080p), 2K (1440p), 4K (2160p) and 8K (4320p). The higher the resolution of your screen, the higher the video quality should be. However, there are other factors to consider: download speed, amount of free space, and device performance during playback.

Why does my computer freeze when loading a "Вся правда о циркулярках на примере Прораб 5602" video?

The browser/computer should not freeze completely! If this happens, please report it with a link to the video. Sometimes videos cannot be downloaded directly in a suitable format, so we have added the ability to convert the file to the desired format. In some cases, this process may actively use computer resources.

How can I download "Вся правда о циркулярках на примере Прораб 5602" video to my phone?

You can download a video to your smartphone using the website or the PWA application UDL Lite. It is also possible to send a download link via QR code using the UDL Helper extension.

How can I download an audio track (music) to MP3 "Вся правда о циркулярках на примере Прораб 5602"?

The most convenient way is to use the UDL Client program, which supports converting video to MP3 format. In some cases, MP3 can also be downloaded through the UDL Helper extension.

How can I save a frame from a video "Вся правда о циркулярках на примере Прораб 5602"?

This feature is available in the UDL Helper extension. Make sure that "Show the video snapshot button" is checked in the settings. A camera icon should appear in the lower right corner of the player to the left of the "Settings" icon. When you click on it, the current frame from the video will be saved to your computer in JPEG format.

What's the price of all this stuff?

It costs nothing. Our services are absolutely free for all users. There are no PRO subscriptions, no restrictions on the number or maximum length of downloaded videos.