background top icon
background center wave icon
background filled rhombus icon
background two lines icon
background stroke rhombus icon

Download "Как подкачать гидроаккумулятор самому?"

input logo icon
Video tags
|

Video tags

подкачать гидробак
как подкачать гидробак
Subtitles
|

Subtitles

subtitles menu arrow
  • ruRussian
Download
00:00:00
good afternoon, today we’ll talk about pumping
00:00:03
air into the hydraulic accumulator of
00:00:06
water supply systems from a well from a well,
00:00:09
including several houses,
00:00:11
when it needs to be done, how it
00:00:14
needs to be done and with what we will
00:00:18
use a regular car
00:00:19
compressor that is in every
00:00:21
passenger car and we will connect
00:00:23
it to the battery 12 exactly the same volt
00:00:26
that anyone needs in a car
00:00:30
when it is necessary to pump up the air, when the
00:00:33
pressure often begins to spike when
00:00:35
turning on the water in the tap and when the hydraulic tank
00:00:39
begins to condense heavily, first
00:00:41
a little about the design of the hydraulic tank, how it
00:00:44
lunges, not everyone understands it, everything is
00:00:46
quite simple here but many people don’t understand,
00:00:49
including those who collided for the first time,
00:00:53
here is the metal volume itself, there is a pear in it, the
00:00:57
pear comes out through
00:01:01
the hole of the storm battle flange,
00:01:05
here the flange is visible that there is rust,
00:01:08
why because firstly the hydraulic tank
00:01:11
has been standing for a long time, secondly,
00:01:13
no one has controlled the air in it since birth, so it
00:01:15
often drains in this place,
00:01:17
water accumulates, begins to rust, the
00:01:21
bulb comes out of the flanges with a hole in
00:01:24
this direction, that is, water
00:01:26
is always in the bulb,
00:01:27
but between the bulb and the body of the hydraulic tank
00:01:30
there is air, the air there must be
00:01:33
under pressure, the pressure is pumped by a
00:01:36
pump with
00:01:37
exactly the same pump as you
00:01:39
pump the tires of your car, here are
00:01:42
the grains, the choke is absolutely one to one, like the
00:01:44
wheels of a car, the correct setting
00:01:49
of the hydraulic tank will allow you to avoid condensation as much as possible,
00:01:51
that is, when you are in a
00:01:52
vertical position, the hydraulic accumulator,
00:01:54
air fills the space
00:01:56
between the body and the pear and the pear
00:01:58
is located inside, that is, the
00:02:00
air layer does not form the wall of the pear rests against a
00:02:04
metal wall and therefore there is
00:02:07
the least amount of condensation on the outside,
00:02:09
including the bulb
00:02:11
in the hydraulic accumulator wears out evenly; it rubs less against the
00:02:14
walls inside; between it, between the bulb and the
00:02:17
body, there should be talc and in good
00:02:20
films like a bet or not a GI, this
00:02:22
tank is enough, so the bulb lasts a
00:02:24
long time takes longer and wears out less,
00:02:27
including when you place the hydraulic tank
00:02:28
vertically and attach the
00:02:31
hydraulic tank to the wall by itself, look it is
00:02:32
horizontal, that is, it has legs
00:02:34
located in this part, that is, often
00:02:36
the hydraulic tank is placed horizontally, this is
00:02:37
wrong, it is better to place it vertically
00:02:39
or on the legs of the well with each a caisson
00:02:42
or like this, a horizontal
00:02:44
hydraulic accumulator on the wall, then it
00:02:46
will wear out naturally, it will
00:02:48
last longer for you, and a very important point
00:02:49
is the grinding of yours,
00:02:51
many companies simply don’t do it, there are
00:02:54
burrs in the end, this idea, the
00:02:56
burrs grind the pear, so the
00:02:58
correct air setting is the
00:03:01
air pressure correctly setting the hydraulic tank
00:03:02
on the left will allow you to extend
00:03:05
the hydraulic tank several times
00:03:06
when they are well tuned 10 years background
00:03:08
service life of a stout or huni jeep which is the
00:03:10
same thing the same factory is doing
00:03:13
now let's see when the system to the right
00:03:17
it works correctly here we adjusted the
00:03:18
battery settings or pressure what is
00:03:21
happening that is when
00:03:22
the pump turns on when the pump turns off what the pressure gauge
00:03:25
shows us I’ll open the tap with
00:03:28
cold water and we’ll look at what’s
00:03:32
going on here on the pressure gauge the
00:03:34
pressure gauge showing water in the
00:03:37
water supply system this pressure gauge shows the
00:03:39
water pressure after the filter, that is,
00:03:42
this is the real pressure between the hydraulic tank and the
00:03:44
pump there should be nothing, no
00:03:46
filters under any circumstances, they will only
00:03:49
cause the Harley to work incorrectly, the pressure does
00:03:52
not drop,
00:03:57
the pump has not yet turned on, we see that the
00:03:59
private is not upset, it is ideal when the
00:04:02
pump activation pressure is approximately
00:04:06
22 and 1 2 1 atmospheres,
00:04:09
two point one tenths of the sphere, then it should
00:04:11
spin the pump should pump up to
00:04:14
approximately three and a half atmospheres and
00:04:16
turn off here Lyoshka razr guli ravana,
00:04:19
that is, it is clear that the spring has weakened and we
00:04:22
see that the pump is so far and the film turned out I
00:04:23
wanted to go out one and a half years ago,
00:04:26
no one has adjusted anything here, and the system has been
00:04:29
working for five years now, by the way
00:04:31
this is said to be the quality of both
00:04:33
the components and the hydraulic tank from the stout company,
00:04:36
you see and the pressure drops, it continues to
00:04:39
drop, the pump still doesn’t turn on
00:04:41
because if the pump turned on, we
00:04:43
saw the arrow going up,
00:04:47
but it doesn’t go up yet, so it drops,
00:04:50
drops, let’s flush the toilet to
00:04:52
speed up the release of water from the hydraulic tank
00:04:57
now the pear is pressed with its pressure
00:05:00
plus the air between the pear and the
00:05:03
walls of the housing will press on the water and the water
00:05:06
is forced out into the water supply system,
00:05:08
that is, it comes from there from the
00:05:10
well through the pipe, the party running
00:05:12
fitting is here at the pressure and then
00:05:14
it is forced out through the filter
00:05:17
the water supply has already started we see that these arrows are equal,
00:05:19
so we don’t need to clean the filter in
00:05:22
any way because the pressure drops and we
00:05:25
found everything doesn’t turn on, so the pump
00:05:27
turned on, that is, it turned on at
00:05:29
almost 1 atmosphere, this is very little
00:05:32
setting is incorrect, so
00:05:34
the customer called us and said come to
00:05:36
the construction site, don’t close the system the
00:05:37
tap will look at how long it takes to
00:05:39
unscrew the pump, the pump should
00:05:43
turn off at 3 plug-in atmospheres,
00:05:45
now there is no water flow,
00:05:48
but the pump is working and it fills the water into the
00:05:53
accumulator, that is, it comes from the
00:05:55
well like this and
00:05:57
pump the pear into the pear and
00:06:00
air pressure is created between the
00:06:02
pear and the pear. the body rises. now
00:06:04
it expands in this way in the hydraulic tank, let
00:06:09
's see how much pressure will
00:06:11
occur
00:06:12
at which the pump will turn off, that
00:06:16
is, essentially the water pressure in the
00:06:18
system, the
00:06:19
game tank maintains water pressure for a while so that the
00:06:21
pump does not work constantly, that
00:06:24
is, these are the cyclical operation of the pump,
00:06:26
this is a normal system, normal operation of the
00:06:28
system water supply from a well or
00:06:30
borehole, we
00:06:31
see that it gives decently and gives for
00:06:33
quite a long time the first mistake that I
00:06:37
saw was this mood
00:06:39
disorder or pressure, that is, the
00:06:40
spring has weakened over five years and
00:06:43
it needs to be adjusted a little, as long as
00:06:47
everything shows us the pump turned off at an hour the
00:06:49
iris helped out the pump for 3 and a half,
00:06:51
that is, the upper pressure is normal, the
00:06:53
lower pressure is low, so we will
00:06:55
regulate everything and or pressure and
00:06:56
adjust the air in the hydraulic tank. Now I
00:06:59
will show you how the system works before
00:07:03
adjustment when
00:07:05
there is no air in the hydraulic accumulator, that is, this is what
00:07:07
happens in this case, for this I will release
00:07:09
all the air from the coffin we
00:07:15
see that the water pressure also drops,
00:07:19
why because the pine trees turn on, it’s
00:07:21
too early for it to turn on,
00:07:22
but at the same time, when I release water into the air
00:07:27
from the hydraulic tank, the water
00:07:28
comes to the bulb because the pressure
00:07:30
between the bulb and the body of the hydraulic accumulator
00:07:33
decreases, I release the air in this
00:07:35
way and the water pressure also
00:07:40
drops because that the balance in air
00:07:43
and water for the whole and the pressure is essentially
00:07:46
not equal, we see that the pressure has
00:07:54
practically dropped to unity,
00:07:57
that is, we have removed all the air from the
00:07:59
hydraulic tank, now the pump has turned on again, the
00:08:04
pump setting was incorrect, it
00:08:09
happened and began to pump water into the
00:08:11
hydraulic tank, but now there is air The hydraulic accumulator will completely
00:08:14
leave the space between the bulb
00:08:17
and the
00:08:21
water pressure in the
00:08:24
water supply system will increase very quickly. I completely bled all the
00:08:30
air out of the hydraulic tank and the pressure
00:08:33
dropped a little again because
00:08:36
we'll turn it off now. I'll open the
00:08:37
cold water. You can see how quickly the water drops, the
00:08:42
water pressure in In the water supply system,
00:08:45
water now flows due to the pressure
00:08:46
that the pipes create, also the masters
00:08:50
moved 50 meters each and the pipe in its
00:08:54
diameter increases slightly with the pressure,
00:08:56
we see that the water pressure drops
00:08:59
very quickly, the water displaces the pipe
00:09:03
displaces the water due to compression, and now
00:09:07
the pump should turn on, come on I
00:09:09
'm bored of water, we close the tap, the
00:09:12
pressure quickly builds up in the main line and the
00:09:17
pump turns off again, opening the water again, the
00:09:21
pressure quickly drops like crazy,
00:09:28
it will go to one, that is, literally there are
00:09:30
5 liters of water coming out of the
00:09:33
water supply system, even probably less and the
00:09:38
pressure drops again,
00:09:43
look now we want a pump Yes, the
00:09:49
pump turns on and then the
00:09:53
pressure quickly builds up, the pipes expand, the
00:09:55
water supply systems in the main line expand, and then
00:09:58
the pump turns off again,
00:10:01
turning on the pump so frequently won’t lead to anything good. When
00:10:02
you have
00:10:04
a Taras problem, it means the air
00:10:05
has come out of the hydraulic accumulator and you need to
00:10:08
pump up the hydraulic tank. This often happens
00:10:13
when the line is short, let's say 5-10
00:10:18
meters, in this case the needle starts to
00:10:21
rattle, or rather, not the needle starts to
00:10:25
rattle, but even the pump starts to rattle, the relay
00:10:28
very quickly builds up pressure, the
00:10:31
needle jumps, that is, a drop rises a
00:10:33
fall in the case like this down up down up
00:10:35
down up and this
00:10:39
indicates that there is no air in the
00:10:41
hydraulic accumulator system of the
00:10:44
water supply systems all the air has come out of the hydraulic tank
00:10:48
what needs to be done to pump
00:10:51
air into the hydraulic accumulator the system for supplying
00:10:53
water from a well or from a well you
00:10:55
need to turn off the automatic
00:10:59
power supply to the pump and open the tap and
00:11:03
you can open any cold water tap in
00:11:06
at home or to everyone on the screen, a well or
00:11:09
a well, which is faster, so that there is a free
00:11:13
exit of water from the water supply system, you even
00:11:18
need to remove the cap on the top
00:11:20
cap on the hydraulic tank with a hall match to
00:11:24
which we will connect the pump when
00:11:30
we supply air to the hydraulic tank
00:11:33
in the volume between the bulb and the
00:11:37
accumulator body, it will come in
00:11:40
so be forced to displace the water that
00:11:42
is in the bulb in the deflated state
00:11:44
of the hydraulic accumulator, we have the bulb under
00:11:47
full pressure, the water pressure
00:11:49
from inside the bulb is completely pressed against the
00:11:52
walls of the hydraulic accumulator, so
00:11:55
we have
00:11:56
practically no air there now, so when we
00:12:00
pump air into the gap between the bulb and the
00:12:04
hydraulic tank body, there will be water
00:12:07
it will be forced out of the pear, it
00:12:09
will be forced out through the common hole of the hydraulic tank, that
00:12:11
is, into the water supply system, so the
00:12:13
pressure will naturally increase, the
00:12:15
water pressure in the system will be plants
00:12:18
because you have the pump turned off, this needs to
00:12:22
be understood, but at the same time, you will be
00:12:24
monitoring here not the air pressure
00:12:26
in the hydraulic tank, but
00:12:28
the pressure water, but
00:12:30
you will control the air pressure in the hydraulic tank system using the
00:12:33
compressor, we take a
00:12:37
regular car compressor,
00:12:38
here it is, a regular battery,
00:12:41
we connect to the hydraulic accumulator at
00:12:44
the top of the fitting
00:12:46
in which you supply air, turn off the
00:12:50
pump, open the tap and
00:12:53
water supply system and start supplying
00:12:55
electricity to the pump for those who have a
00:12:58
standard one a standard 12 volt plug,
00:13:02
I took this wire to show how to
00:13:04
connect to us here plus an
00:13:07
ordinary one on the side we have a minus, that is,
00:13:09
we put a plus in the positive terminal
00:13:12
here and the minus post with an ordinary wire
00:13:14
we close the Watson minus and begin to
00:13:17
pump air into the hydraulic tank, I
00:13:34
draw your attention that the taps are open
00:13:37
and the water is slowly coming out of the
00:13:39
poet from the hydraulic accumulator,
00:13:42
air comes in and the water
00:13:44
comes out of the pear,
00:13:48
that is, we supply air, it fills the
00:13:51
volume between the body and the pear,
00:13:53
naturally the water in the pear is compressed and
00:13:56
slowly leaves the water supply system,
00:13:59
look, the pressure has risen about what I
00:14:00
said, that is, the water pressure inside
00:14:03
rises,
00:14:05
but about the fact that the air presses on the
00:14:08
membrane between the membrane housings and
00:14:10
the water is slowly displaced by the one
00:14:12
that was in your pear hydraulic tank, let's
00:14:17
look at the pressure, it's
00:14:20
almost two and a bit,
00:14:23
turn off our
00:14:25
compressor, turn on the compressor and
00:14:28
release the pressure, pumped a little up to
00:14:31
18 up to 18 we release the pressure by
00:14:34
unscrewing here our
00:14:39
nozzles ours called pinchuk we release we
00:14:42
control we check here we let in we control we
00:14:49
let in we control that
00:14:55
is, when we raise we lower we press we
00:15:00
control it should be 18
00:15:13
all 18 now we turn on the pump we close the
00:15:18
tap and we adjusted the pressure and before
00:15:22
start the system work I'm up to a little
00:15:26
explanation here at the moment we have
00:15:28
water pressure 0 pressure in the hydraulic tank 18
00:15:32
this indicates that the air
00:15:36
has completely compressed the
00:15:38
bulb in the hydraulic tank and you hear how it
00:15:42
will teach it as if it is empty inside
00:15:44
while the bulb is completely inside with compressed
00:15:46
air as soon as we Let's start turning on the
00:15:49
water and thereby turning on the pump, we have
00:15:52
an expansion of the pear, it expands and the
00:15:55
back pressure of air on the
00:15:58
pear begins, so at the moment when the pump is turned on,
00:16:00
we should have one, it will start to be two wholes,
00:16:03
move away from the atmosphere the moment of turning off is
00:16:05
about 3 3 and a half, and let's set it up, start the
00:16:10
system, turn it on the pump water is
00:16:14
on now, here we have a key,
00:16:16
we have the role of pressure like this, we will
00:16:18
set up the pressure switch, it is
00:16:21
very convenient and you can unscrew the nut
00:16:24
here, from which they hold the body of the
00:16:26
relay itself, we took two nuts,
00:16:31
one nut is large, the other nut is a
00:16:33
small large nut we adjust the
00:16:37
displacement of the range by suppressing the upper
00:16:39
side, that is, we move the range itself
00:16:41
up like this, and with the small nuts, when
00:16:44
we tighten it, we expand the range,
00:16:46
when we unscrew it, we narrow the range, that
00:16:48
is, we need to increase the total pressure
00:16:51
using the large nut, we tighten it
00:16:54
a few turns,
00:16:55
here I directed the small one We
00:16:58
unscrew the nut a little bit
00:17:00
to narrow this range and
00:17:02
thereby we will achieve by working a
00:17:05
suppression interval of about two two and one three and a
00:17:10
half four that's how we'll make
00:17:13
the settings completed and look what I
00:17:16
want to show you I specially raised
00:17:18
the pressure now a little more than normal to 4
00:17:20
atmospheres
00:17:21
so that you understand how correctly
00:17:25
the hydraulic accumulator sounds, even despite the fact that the
00:17:27
pressure is exceeded, look, we are
00:17:30
knocking from above, you hear fr,
00:17:36
this indicates that between the body of
00:17:39
the hydraulic tank and the pear there is air everywhere, even
00:17:43
in the lower part it begins to appear, how
00:17:46
many pears here begin to touch the
00:17:47
wall the body is only here now we see the
00:17:49
pressure a little when I lower it, I’m three and a
00:17:51
half and there will be an even more ringing
00:17:55
sound, that is, even with the
00:17:58
hydraulic tank pumped through the air, we see that the bulb
00:18:00
barely touches the bottom of the walls, so
00:18:03
when the hydraulic tank is adjusted correctly,
00:18:07
the minimum amount of condensate and the
00:18:11
pump rarely turns on, that is, until
00:18:14
the volume of water comes out, the
00:18:16
pressure will not go up to two atmospheres,
00:18:18
the pump will not turn on and the water output is 80
00:18:22
in the hydraulic tank, well, about 40 maximum 50
00:18:24
liters with the correct settings,
00:18:27
finally, a couple of important points, always
00:18:30
follow this architecture of the
00:18:32
hydraulic tank to drink and the running role
00:18:35
water supply pressure from the pump here to the 5th
00:18:39
annual point here where the
00:18:41
pressure and pressure gauge and pressure switch are controlled and the
00:18:43
supply through a 100 micron filter is the
00:18:46
water supply system. It is precisely this
00:18:51
device and such a layout and
00:18:53
architecture that made it possible to obtain
00:18:55
long-lasting water supply systems that
00:18:57
least need to be adjusted because
00:18:59
you relieve the pressure at the point where the
00:19:02
pumps press David the hydraulic tank is important
00:19:04
when the hydraulic tank is located in a different place
00:19:06
further from the fender when the pipe inlet from the
00:19:09
pump is also in a different place the system
00:19:11
works a little unbalanced and
00:19:13
there may be problems with setting up
00:19:14
the water supply these are the systems we
00:19:17
install at our customers’ sites every day
00:19:19
and they are extremely
00:19:21
happy because this layout of
00:19:24
the water supply takes up little space, you can
00:19:26
place a hydraulic accumulator of
00:19:28
any size on top of the toilet,
00:19:31
a water heater,
00:19:32
that is, there is enough space and all
00:19:36
these devices are located in the bathroom in one
00:19:41
vertical architecture, we have a lot of work
00:19:45
on Instagram, look at
00:19:48
the link, what’s our name on Instagram, look
00:19:51
our works there articles contain detailed
00:19:52
prices, especially the latest
00:19:54
works, current prices for
00:19:56
today, be healthy
00:19:58
all the best, goodbye

Description:

И избавиться от конденсата. Используем обычный автомобильный компрессор и аккумулятор. Ответим на вопросы когда подкачивать, зачем подкачивать и как подкачивать гидроаккумулятор для системы водоснабжения. Настройка давления воздуха и насоса. Перечень устанавливаемого оборудования: - скважинный насос Aquario 55-75 или колодезный насос Aquario 2-40-100WA c поплавком /Италия/ (для колодцев с маленьким количеством воды) - нержавеющая цепь для насоса 3 мм /Россия/ - нержавеющие карабины для крепления насоса к цепи 6 мм /Россия/ - магистраль от источника водоснабжения (колодец) до объекта - это две трубы: пищевая дюймовая с водой (самая толстая стенка - 3мм) и полдюймовая с кабелем насоса для удобной замены CYKLON /Россия/ - соединительные компрессионные ПНД-фитинги JASON /Италия/ - герметизация входа труб в колодец гидропломбой Glims /Россия/ - незамерзающий ввод воды в дом, установка наружного саморегулируемого кабеля с утеплением трубы с глубины промерзания Eastec /Корея/ - при высоком уровне грунтовых вод монтаж внутреннего пищевого саморегулируемого кабеля в трубу на всю длину магистрали с опуском в колодец Eastec /Корея/ - реле давления насоса – Aquario /Италия/ - дополнительные немецкие автоматы насоса и греющего кабеля для удобного отключения ABB /Германия/ - гидроаккумулятор для воды объемом 24, 50, 80, 100 литров с креплением на стену в удобное место – Stout /Россия-Италия/ - пятиходовой штуцер для подключения реле, манометра , гидробака и фильтра ITAP /Италия/ - удобный манометр системы для контроля за давлением – Stout /Италия/ - самоочистной фильтр с манометром и промывкой который предотвращает выход смесителей из строя – TIM - петля с обратным клапаном для полного слива воды из системы водоподготовки, например, во время длительного отсутствия хозяев, или зимой для полного слива – ITAP /Италия/ - обвязка системы водоподъема качественным толстостенным полипропиленом Berke-Plastik, Kalde /Турция/ Переходите на канал в Яндекс Дзен: https://zen.yandex.ru/id/5fb2cff130456904f909bf62 Телеграм канал: https://t.me/udcomp Группа Вконтакте: https://vk.com/ud_comp Мы в Одноклассниках: https://ok.ru/profile/586597147596 Канал в Одноклассниках: https://ok.ru/video/c6744524ok.ru/video/c6744524 Видео на RUTUBE: https://rutube.ru/channel/23859485/ Полезное на сайте "удачная-компания.рф": https://xn----7sbabq2amqffin7b6c0gi.xn--p1ai/ Заказать любое оборудование можно по электронной почте [email protected] или по телефону (915) 123-2-777. Отправляем во все регионы России. Мы делаем: Дизельное отопление дачи: https://zen.yandex.ru/video/watch/622b6e9bae5d327e07e5e6fb Автономное комбинированное отопление на дровах и электричестве (система может работать полностью без электричества как самотечная): https://zen.yandex.ru/video/watch/622b62b53d5758617115e983 Подробный разбор этой системы: https://zen.yandex.ru/video/watch/62225a7e4edb4f71acaac90e Комбинированное отопление на дизельном топливе и электричестве: https://zen.yandex.ru/video/watch/622b7671a5b41152f4db4941 Отопление дачи только на электричестве с контролем по телефону: https://zen.yandex.ru/video/watch/622b6fad5e4d0a774e2d8fd8 Для Вас мы рекомендуем: Готовые системы зимнего водопровода из колодца: https://rutube.ru/video/0c2bace09b25afb2ff16be03b96bdf4f Из скважины с адаптером: https://zen.yandex.ru/video/watch/621f6f0f57c157196268aa57 Из колодца на два дома: https://zen.yandex.ru/video/watch/622b71ceae5d327e07ea6196 Из колодца и центрального водопровода: https://zen.yandex.ru/video/watch/622c5b62e881b82d805d3e72 Из центрального водопровода: https://zen.yandex.ru/video/watch/6220f043e33cf243d8c5c29a Заказать любое оборудование можно по электронной почте [email protected] или по телефону (915) 123-2-777. Отправляем во все регионы России. Обратите внимание на Автономную канализацию "Термо-ЛОС" (termo-los.ru) для самостоятельного монтажа, которая не замерзает и не нужно консервировать: Стандартная станция Термо-ЛОС Авто- 4: https://zen.yandex.ru/video/watch/622c49a0ff8f745e158cb2b8 Для высокого уровня грунтовых вод на 1-4 человека "Термо-ЛОС-Плывун": https://zen.yandex.ru/video/watch/622c482cd6fb0a2f439c643c Для семьи от 2 до 6 человек "Термо-ЛОС-Авто-6": https://zen.yandex.ru/video/watch/622c3c555e4d0a774eec2704 Для 4 и более человек "Термо-ЛОС-Авто-8": https://zen.yandex.ru/video/watch/622c3570ff8f745e1571764b На сайте есть калькулятор для подробной расчета стоимости отопления, водоснабжения и канализации. https://comp-udacha.ru/raschitat-stoimost-vodosnabjenie "удачное-водоснабжение.рф" https://xn----7sbbedjdffajz0deegdb1d3a0g.xn--p1ai/ "удачное-отопление.рф" https://xn----7sblfbauwpegcao7bi4e.xn--p1ai/ "удачная-канализация.рф" https://xn----7sbabaaw3aicqoue6fxcf0ml.xn--p1ai/

Preparing download options

popular icon
Popular
hd icon
HD video
audio icon
Only sound
total icon
All
* — If the video is playing in a new tab, go to it, then right-click on the video and select "Save video as..."
** — Link intended for online playback in specialized players

Questions about downloading video

mobile menu iconHow can I download "Как подкачать гидроаккумулятор самому?" video?mobile menu icon

  • http://unidownloader.com/ website is the best way to download a video or a separate audio track if you want to do without installing programs and extensions.

  • The UDL Helper extension is a convenient button that is seamlessly integrated into YouTube, Instagram and OK.ru sites for fast content download.

  • UDL Client program (for Windows) is the most powerful solution that supports more than 900 websites, social networks and video hosting sites, as well as any video quality that is available in the source.

  • UDL Lite is a really convenient way to access a website from your mobile device. With its help, you can easily download videos directly to your smartphone.

mobile menu iconWhich format of "Как подкачать гидроаккумулятор самому?" video should I choose?mobile menu icon

  • The best quality formats are FullHD (1080p), 2K (1440p), 4K (2160p) and 8K (4320p). The higher the resolution of your screen, the higher the video quality should be. However, there are other factors to consider: download speed, amount of free space, and device performance during playback.

mobile menu iconWhy does my computer freeze when loading a "Как подкачать гидроаккумулятор самому?" video?mobile menu icon

  • The browser/computer should not freeze completely! If this happens, please report it with a link to the video. Sometimes videos cannot be downloaded directly in a suitable format, so we have added the ability to convert the file to the desired format. In some cases, this process may actively use computer resources.

mobile menu iconHow can I download "Как подкачать гидроаккумулятор самому?" video to my phone?mobile menu icon

  • You can download a video to your smartphone using the website or the PWA application UDL Lite. It is also possible to send a download link via QR code using the UDL Helper extension.

mobile menu iconHow can I download an audio track (music) to MP3 "Как подкачать гидроаккумулятор самому?"?mobile menu icon

  • The most convenient way is to use the UDL Client program, which supports converting video to MP3 format. In some cases, MP3 can also be downloaded through the UDL Helper extension.

mobile menu iconHow can I save a frame from a video "Как подкачать гидроаккумулятор самому?"?mobile menu icon

  • This feature is available in the UDL Helper extension. Make sure that "Show the video snapshot button" is checked in the settings. A camera icon should appear in the lower right corner of the player to the left of the "Settings" icon. When you click on it, the current frame from the video will be saved to your computer in JPEG format.

mobile menu iconWhat's the price of all this stuff?mobile menu icon

  • It costs nothing. Our services are absolutely free for all users. There are no PRO subscriptions, no restrictions on the number or maximum length of downloaded videos.